Automatic injection timing of fuel
The cargo swinging in a plane perpendicular to the axis of the muf-
you, axle shaft pressed into the driven coupling half.
A spacer abuts the leading half coupling one con-
ring in the finger of the cargo and the other at the relevant projection. Pru-
the spring retain
the loads on the stop in the sleeve
leading the coupling halves. When
the increase in the frequency of rotation.
cluding a crankshaft
the engine under the action
centrifugal force loads
apart, as a result
what driven half coupling
turns on
tion leading to b
of rotation of kulachko-
new roller that increases
for the advance angle
fuel injection. When
reducing the frequency of rotation.
with regard to the goods under the action-
eat springs converge. Ve
the hub of home cooks-
lost along with cushion
fuel pump in
the opposite side
well rotation that reduce the
increases the advance angle
fuel injection.
Nozzles are used to
injection and spray-
of fuel, as well as for
distribution of its particles
the volume of the chamber share-
of .
The basic element of the nozzle is
is the dispenser having one or more nozzle
holes, forming the torch of injected fuel.
Are the injectors closed and open. In
four-stroke diesel engines use injectors closed
type, nozzle openings which are closed shut
needle. Therefore, the internal cavity in the housing of the spray-
lei injector communicates with the combustion chamber only in the peri-
od of fuel injection.
Turbocharging in diesel engines, i.e. the flow of charge air in
the cylinder under pressure to increase capacity
For supercharged diesel equipped with a turbocharger, SP-
using the energy of exhaust gases. Increasing on-
addition by air cylinders, the turbocharger increases
combustion efficiency at the same time increased dose
the injected fuel. This gives you the opportunity to increase
the effective power of the diesel up to 30 %. However, the boost increase
Lycium thermal and mechanical tension of the parts
crank and gas distributing mecha-
of mechanisms.
Compressed air compressor is injected into the chamber the CDF
Rania under the pressure of 0,15 — 0,2 MPa. Distinguish:
• 0,15 MPa is low boost;
• 0.2 MPa — the average boost;
• more than 0.2 MPa — high boost.
The cargo swinging in a plane perpendicular to the axis of the muf-
you, axle shaft pressed into the driven coupling half.
A spacer abuts the leading half coupling one con-
ring in the finger of the cargo and the other at the relevant projection. Pru-
the spring retain
the loads on the stop in the sleeve
leading the coupling halves. When
the increase in the frequency of rotation.
cluding a crankshaft
the engine under the action
centrifugal force loads
apart, as a result
what driven half coupling
turns on
tion leading to b
of rotation of kulachko-
new roller that increases
for the advance angle
fuel injection. When
reducing the frequency of rotation.
with regard to the goods under the action-
eat springs converge. Ve
the hub of home cooks-
lost along with cushion
fuel pump in
the opposite side
well rotation that reduce the
increases the advance angle
fuel injection.
Nozzles are used to
injection and spray-
of fuel, as well as for
distribution of its particles
the volume of the chamber share-
of .
The basic element of the nozzle is
is the dispenser having one or more nozzle
holes, forming the torch of injected fuel.
Are the injectors closed and open. In
four-stroke diesel engines use injectors closed
type, nozzle openings which are closed shut
needle. Therefore, the internal cavity in the housing of the spray-
lei injector communicates with the combustion chamber only in the peri-
od of fuel injection.
Turbocharging in diesel engines, i.e. the flow of charge air in
the cylinder under pressure to increase capacity
For supercharged diesel equipped with a turbocharger, SP-
using the energy of exhaust gases. Increasing on-
addition by air cylinders, the turbocharger increases
combustion efficiency at the same time increased dose
the injected fuel. This gives you the opportunity to increase
the effective power of the diesel up to 30 %. However, the boost increase
Lycium thermal and mechanical tension of the parts
crank and gas distributing mecha-
of mechanisms.
Compressed air compressor is injected into the chamber the CDF
Rania under the pressure of 0,15 — 0,2 MPa. Distinguish:
• 0,15 MPa is low boost;
• 0.2 MPa — the average boost;
• more than 0.2 MPa — high boost.